These 8 kinds of erroneous car care, keep children and owners are doing!

These 8 kinds of erroneous car care, keep children and owners are doing!

Not to mention novice drivers. Some old drivers still make a lot of commonsense mistakes in car maintenance. Are you still doing these 8 wrong practices?

1, under the hot sun car wash

Car washing under the hot sun, sunlight hitting the car body, and focusing through the water droplets can damage the car paint, which is why the car body should be wiped clean after car washing. In addition, when the car wash must keep the appearance of the car air conditioner dry, if the car air conditioner is not accidentally wet, it will affect the life of car air conditioning.

2, waxing with a circle

Many people wax the body habitually in a circle, which is incorrect. The correct method of waxing is straight line, horizontal and vertical lines alternately, and then press the last step in the direction of rainwater flow, so as to achieve the effect of reducing concentric rings of halo on the paint surface.

3, excessive oil added

When the oil in the engine oil pan is insufficient, the friction between the bearing and the journal will be poor due to the small amount of oil, which will increase the degree of wear, and even cause a burnt shaft accident. However, if there is too much oil, the crankshaft shank and the big end of the connecting rod will produce violent agitation when the engine is working, which not only increases the internal power loss of the engine, but also increases the oil splashed on the cylinder wall, resulting in burning oil failure. Therefore, the oil in the oil sump of the engine should be controlled between the upper and lower scoring lines of the oil dipstick.

4, the bolt is too tight

There are many fasteners on the car that are connected with bolts and nuts. It should be ensured that it has enough pre-tightening force, but it cannot be tightened too tightly. If the tightening is too tight, on the one hand, the connection member will be permanently deformed under the action of external force; on the other hand, the bolt will be permanently deformed by tension, the pre-tightening force will be reduced, and even a sliding buckle or breaking phenomenon will occur.

5, fan belt too tight

Summer temperatures are too high, and some drivers think that raising the tightness of the fan belt can improve the cooling effect of the engine. Therefore, the tightness of the fan belt is constantly increased, causing the fan belt to become tight. It is not true that this is wrong. The fan belt should be kept tight and tight, because over-tightening will lead to excessive bearing load, increased wear and tear, increased power consumption, and will also cause the water pump shaft to bend, the belt will be stretched and deformed, and the service life will be shortened.

6, look for imported tires

Some people like to buy tires particularly like to emphasize "import." However, one of the most fatal flaws for domestic users is the inapplicability of new tires that have been introduced abroad. On the contrary, some foreign brands' tyres have been added to the tires by a layer of cord fabric after domestic joint venture production according to the domestic road conditions, which greatly enhances the impact resistance of the sidewalls. The tires produced by the joint venture can be completely replaced in terms of performance. Imported goods.

7, the new battery is not charging

The first charge of the battery is called the initial charge, and the initial charge has a great influence on the service life of the battery. If it is not recharged, it will be directly used when adding “water”. The capacity of the battery will not be high and the service life will be shortened; if it is directly charged, it will also shorten the life. Usually, the initial charge of the battery is performed after charging the electrolyte and charging it with a small current for about 1 hour.

8, long-term parking without

Some people are not willing to use the car after the car, only to drive out to play when the holiday, in fact, such a car is also very hurt the car. Parts of the transmission such as the engine and the gearbox are rusted due to their direct contact with the air, and the battery will also affect the service life due to long-term natural discharge. The best way is to run the car every few days and run for thirty to forty minutes. In addition, it is always a short-distance car to hurt the car, the car is moving at any time but not far away, is an important reason for injury.


LINA Two Roll Mill with PLC Control System


All types of LINA Two Roll Mixing Mill can install with PLC (Programmable Logic Controller) system to monitor the machine unit`s working process, such as mixing time control, temperature control and data import and export. A touch screen is installed to manage the system and shows graphic data. In addition, an Ethernet communication interface and 20% of the control points can be reserved. 


9 Inch Heating Type Rubber Mil


LINA Precise PLC Control Two Roll Rubber Mill For Rubber

Excellent appearance: LINA new design laboratory roll milling machinewith comprehensive optional functions and securedevices, which ensure the accuracy of formulaand high efficiency.

Safe guaranty: The roller adopts 360 degrees emergency and reverse braking devices, infrared automatic detection and ergonomics security to ensure operator's safety.

Intelligent operation: LINA Lab Two Roll Open Mill for product test PLC intelligent soft control system is easy to import or export data and record. Extremely accuracy in control and measurement of mixing temperature and ratio.

PLC intelligent control system: 1. Real-time data record and export of kneading time, temperature (mixing chamber and front/rear rotors), ram pressure, current, torque and recipe code. 2. The control system can be set up to 20 mixing steps, save 20 recipe spaces. 3. The control system is capable of remote importing of the process recipe and data monitoring, and communicating with MES via Ethernet communication interface. 4. An Ethernet communication interface and 20% of the control points are reserved. 

PLC DevicePLC





22 Inch Heating Type Rubber Mil


Specifications of LINA Lab Two Roll Milling Machine

No.

Item

Specifications

1

Type

LN-120/4

LN-160/6

LN-200/9

2

Roller Diameter

120mm

160mm

200mm

3

Roller face width

350mm

350mm

600mm

4

Linear Velocity 

of Front Roller

18r/min

17r/min

15r/min

5

Velocity Ratio 

of Rollers

1:1.24

1:1.29

1:1.25

6

Maximum Roll pitch

5mm

5 mm

8mm

 

7

 

Machine Output(kg)

 

0.5-1.5 per time

 

1.5-3 per time

 

3-8 per time

8

Electric heater

3KW

4KW

6KW

9

Motor Power

3.75/5.5KW

5.5KW

11KW

10

Total Weight

About1000KG

About 1000KG

About 1200KG

11

External 

Dimensions(mm)

About1650

*600*1150

About 1650* 600*1150

About 2200* 830*1500

 

Specifications of LINA Mass Production Open Mill Machine

No.

Item

Specifications

1

Type

LN-300/12

LN-360/14

LN-400/16

LN-450/18

LN-550/22

LN-560/24

2

Roller Diameter

300mm

360mm

400mm

450mm

550mm

560mm

3

Roller face width

700mm

900mm

1000mm

1200mm

1500mm

1530mm

4

Linear Velocity

 of 

Front Roller

11r/min

12r/min

10r/min

10r/min

8r/min

8r/min

5

Velocity Ratio of Rollers

1:1.3

1:1.3

1:1.3

1:1.3

1:1.35

1:1.3

6

Maximum Roll 

pitch

10mm

10mm

10mm

12mm

16 mm

15mm

7

Machine

 Output(kg)

15-18 per time

15-25 per time

20-35 per time

30-50 per time

50-70 per time

50-70 per time

8

Motor Power

15KW

37KW

45KW

55KW

110KW

160KW

9

Total Weight

About 3000KG

About 6500KG

About 8000KG

About 10000KG

About 22000KG

About 22500KG

10

External Dimensions(mm)

3000* 1200*1100

4200* 1800*1800

4920* 1780*2100

5200* 1880*2100

 6650* 2740*2100

 6850* 2840*2100

 

PLC Control Two Roll Mill

PLC Control Two Roll Mill,PLC Control Open Mixing Mill,PLC Control Rubber Two Roll Mill,PLC Control Two Roller Open Mill

LINA Machinery Industrial Co.,Ltd , http://www.linakneader.com