Energy Saving Valuable Minerals Recovery Machine Gravity Gold Spiral Separator

Introduction of Spiral Chute
Spiral separator is a new gravity separation machine. With the water and action of gravity friction force, minerals would be separated by the different gravity and get heavy, middling and light products.
Spiral concentrator is made of the fiberglass lined with wear-resistant polyurethnane and corundum cover, with feature of anti corrosion, rust and wear resistant.
It's the most suitable equipment for mining and ore beneficiation, especially for placer mining at seaside, riverside, sand bank and stream bank. It is of low water consumption, small floor area, high concentration and recovery ratio, high adaptability, etc


Application of spiral concentrator
It's applicable to metal and non-metal ores with adequate density difference, like iron, chromite, pyrite, tin ore, tungsten, tantalum, niobium, gold ore, colliery, monazite, rutile and Zirconium.
It can easily adopt to different raw material size, density, ore grade and feed volume. Spiral chute is suitable for treatment of 0.6-0.03mm lode and placer, but high mud content is bad for separation. At present, spiral chute has been widely used in the treatment of iron ore, tungsten, tin ore, niobium tantalum ore, coastal and riverside placer and gold ore.

Working Principle of Spiral Chute

1) Stick up the spiral chute, adjust vertical line, and fix it to a proper place with hob ore timber.
2) Deliver the ore slurry to the two feeding opening at top of the spiral chute with the help of sand pump, add supplementary water to adjust slurry thickness. 
3) Then slurry flows down automatically and rotarily from the top. Ore and sand can be divided under rotary steam and centrifugal force according to the slurry's different specific gravity, grain size and shape. 
4) Next, final ore flows to the final ore hopper and coveyed out by pipe and picked up, and final sand flows to final sand hopper and coveyed out by pipe to sand pond. Then remove the sand pump. That is the whole concentrating process.

Structure of fiberglass spiral chutes

Our spiral chute is a gravity separation equipment of separation different weight mineral by inertial centrifugal force pulp produced in helix turning motion. 

1. Separation Hopper           2. Feeder Trough                   3. Spiral Section  
4. Stand                                5. Ore Receiving Hopper       6. Annular Collecting Hopper

1. Reasonable structure and small occupation area.

2. High recovery, high efficiency, and precise separation

3. Non-required power

4. anti corrosion, rust and wear resistant

5. Simple installation and Minimum maintenance requirements.

6. Low operating cost and long working life.

7. Strong adaptability to fluctuation of feeding amount, density, size and grade

Technical Parameters of Spiral Chute

Company Information
Victor is a large mineral processing manufacturer for 15 years history, with covering an area of 48,000 square meters and 20,000 square meters for workshop, with various large modernized machinery facilities, professional R&D team and installation team.
With 32% market share in China and the rest to overseas, already successfully exported to over 50 countries, such as USA, England, Australia, Brazil, Turkey, Italy, Russia, South Africa, Zimbabwe, Sudan, Ghana, Congo, Morocco, India,Indonesia, Malaysia, Philippines, North Korea, Mongolia, Vietnam, Thailand etc.
Our goal is to provide one-stop service for you and assist you to solve all problems from investment to his return in the field of mining, including the preliminary mineral analysis, mineral processing test, engineering design, equipment debugging and technical training etc..
We are expert especially at mining separating and lab mining plant, main products as below:
Gold trommel wash plant
Shaking table
Spiral chute separator
Centrifugal gold concentrator
Jig separator machines
Waste recycling machine
Grinding and mill crushe
Flotation cell machine
Magnetic separator
Laboratory mining plant

Contact

Introduction of Spiral Chute
Spiral separator is a new gravity separation machine. With the water and action of gravity friction force, minerals would be separated by the different gravity and get heavy, middling and light products.
Spiral concentrator is made of the fiberglass lined with wear-resistant polyurethnane and corundum cover, with feature of anti corrosion, rust and wear resistant.
It's the most suitable equipment for mining and ore beneficiation, especially for placer mining at seaside, riverside, sand bank and stream bank. It is of low water consumption, small floor area, high concentration and recovery ratio, high adaptability, etc


Application of spiral concentrator
It's applicable to metal and non-metal ores with adequate density difference, like iron, chromite, pyrite, tin ore, tungsten, tantalum, niobium, gold ore, colliery, monazite, rutile and Zirconium.
It can easily adopt to different raw material size, density, ore grade and feed volume. Spiral chute is suitable for treatment of 0.6-0.03mm lode and placer, but high mud content is bad for separation. At present, spiral chute has been widely used in the treatment of iron ore, tungsten, tin ore, niobium tantalum ore, coastal and riverside placer and gold ore.

Working Principle of Spiral Chute

1) Stick up the spiral chute, adjust vertical line, and fix it to a proper place with hob ore timber.
2) Deliver the ore slurry to the two feeding opening at top of the spiral chute with the help of sand pump, add supplementary water to adjust slurry thickness. 
3) Then slurry flows down automatically and rotarily from the top. Ore and sand can be divided under rotary steam and centrifugal force according to the slurry's different specific gravity, grain size and shape. 
4) Next, final ore flows to the final ore hopper and coveyed out by pipe and picked up, and final sand flows to final sand hopper and coveyed out by pipe to sand pond. Then remove the sand pump. That is the whole concentrating process.

Structure of fiberglass spiral chutes

Our spiral chute is a gravity separation equipment of separation different weight mineral by inertial centrifugal force pulp produced in helix turning motion. 

1. Separation Hopper           2. Feeder Trough                   3. Spiral Section  
4. Stand                                5. Ore Receiving Hopper       6. Annular Collecting Hopper

1. Reasonable structure and small occupation area.

2. High recovery, high efficiency, and precise separation

3. Non-required power

4. anti corrosion, rust and wear resistant

5. Simple installation and Minimum maintenance requirements.

6. Low operating cost and long working life.

7. Strong adaptability to fluctuation of feeding amount, density, size and grade

Technical Parameters of Spiral Chute

Company Information
Victor is a large mineral processing manufacturer for 15 years history, with covering an area of 48,000 square meters and 20,000 square meters for workshop, with various large modernized machinery facilities, professional R&D team and installation team.
With 32% market share in China and the rest to overseas, already successfully exported to over 50 countries, such as USA, England, Australia, Brazil, Turkey, Italy, Russia, South Africa, Zimbabwe, Sudan, Ghana, Congo, Morocco, India,Indonesia, Malaysia, Philippines, North Korea, Mongolia, Vietnam, Thailand etc.
Our goal is to provide one-stop service for you and assist you to solve all problems from investment to his return in the field of mining, including the preliminary mineral analysis, mineral processing test, engineering design, equipment debugging and technical training etc..
We are expert especially at mining separating and lab mining plant, main products as below:
Gold trommel wash plant
Shaking table
Spiral chute separator
Centrifugal gold concentrator
Jig separator machines
Waste recycling machine
Grinding and mill crushe
Flotation cell machine
Magnetic separator
Laboratory mining plant

Contact

Peugeot And Citroen Are French Automotive Manufacturers, Part Of Group PSA.

The Family Business That Preceded The Current Peugeot Company Was Founded In 1810, And Manufactured Coffee Mills And Bicycles. On 20 November 1858, Émile Peugeot Applied For The Lion Trademark. Armand Peugeot Built The Company's First Car, An Unreliable Steam Tricycle, In Collaboration With Léon Serpollet In 1889; This Was Followed In 1890 By An Internal Combustion Car With A Panhard-Daimler Engine.Due To Family Discord, Armand Peugeot Founded The Société Des Automobiles Peugeot, In 1896.

Citroen Was Founded In 1919 By French Industrialist André-Gustave Citroën(1878–1935).  In 1934, The Firm Established Its Reputation For Innovative Technology With The Traction Avant. This Car Was The World's First Mass-Produced Front Wheel Drive Car, But Also One Of The First To Feature A Unitary Type Body, With No Chassis Holding The Mechanical Components.

We Supply The Peugeot And Renault Spare Parts For More Than 5 Years Worldwidely. Peugoet Car Models Such As 206 207 305 306 307 308 405 406 504 505 508 3008 4008 J5 Boxer And So On. Citroen Car Models Such Like Ax C2 C3 C4 C5 C6 Cx Zx Xsara C-Elysee Quatre And So On.

Peugeot And Citroen

Peugeot And Citroen,Citroen Body Parts,Peugeot Body Parts,Citroen Engine System

Jinan Catop Auto Parts Co., Ltd , http://www.jncatop.com