Hitachi ETP Probe,Oxford ETP Probe,ETP Probe For CMI700,PTH Hole ETP Probe Welltronics Technology Limited , https://www.welltronics.cn
1. Conveying preforms automatically with conveyor.Â
2. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the rails simultaneously in the infrared preheater.Â
3. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.Â
4. No contamination and low noise with the air cylinder to drive the action instead of the oil pump.Â
5. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.Â
6. Strong clamping force with high pressure and double crank links to lock the mold.Â
7. Two ways of operating: Automatic and manual.Â
8. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to understand.Â
9. Contamination is avoided for the bottle body.Â
10. Low rejection rate: Less than 0.2 percent.
 
Maximum Volume: 5 litter
Material: HDPE, PP, PVC, PETG etc.
View Stripe matchable
Easy operation
Automatically
1>Double station and single satation
2>Single mould head to six mould head
3>Mutli-layer with View Strip line
4> It can match auto-deflashing device, Leak detector, Chiller and crusher recycle system.
5> The daliy output(24 hours) can reach approximately from 5, 000 to 86, 000; It can produce from 0.2-5L plastic hollow bottle products.
2. Conveying preforms automatically with conveyor.
3. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the rails simultaneously in the infrared preheater.
4. High adjustability to enable the preheater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus.
5. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.
6. No contamination and low noise with the air cylinder to drive the action instead of the oil pump.
7. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.
8. Strong clamping force with high pressure and double crank links to lock the mold.
9. Two ways of operating: automatic and manual.
10. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to understand.
11. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process.
12. Contamination is avoided for the bottle body.
13. Ideal effect of the chilling with the chilling system.
14. Easy installation and starting
15. Low rejection rate: less than 0.2 percent. 
el
JMX-50
JMX-60
JMX-60D
JMX-70D
JMX-80
max.product volume(l)
2.5
6
2
6
25
dry cyle(pc/h)
1500
1200
700*2
600*2
600
screw diameter(mm)
50
60
60
70
80
screw l/d ratio(l/d)
24-30
24-30
24-30
24-30
25-30
screw drive power(kw)
11-15
15-18.5
15-18.5
18.5-30
37-45
screw heating capacity(kw)
7.8-8.5
10.8-12
10.8-12
12-14.5
16-20
output of hdpe(kg/h)
30-35
60-68
60-80
70-85
120-140
clamping force(kn)
35
68
35
68
200
platen distance(mm)
138-368
178-538
138-368
178-538
400-900
capacity(l)
Â
Â
Â
Â
4.8
max.die diameter(mm)
90
150
90
150
300
central distance of bi-die(mm)
110-130
130-200
130-150`
150-200
Â
max.die diameter(bi-die)(mm)
55
100
80
100
Â
central distance of three-die(mm)
80-110
100-120
80-110
110-140
Â
max.die diameter(three-die)(mm)
40
60
40
70
Â
central distance of four-die(mm)
60-85
60-85
60-85
70-100
Â
max.die diameter(four-die)(mm)
25
30
23
45
Â
die heat capacity(kw)
Â
Â
Â
Â
16
the average consumption(kw/h)
12.5
16.5
16.5
18.5
32
blowing pressure(mpa)
0.6
0.6
0.6
0.6
0.8
air volume(m/min)
0.4
0.5
0.4
0.4
0.8
cooling water pressure(mpa)
0.2-0.3
0.2-0.3
0.3
0.3
0.3
water consumption(l/min)
30
50
60
70
80
oil pump drive power(kw)
5.5
5.5
5.5
5.5-7.5
22
size of machine(l*w*h/min)
2.8*1.8*2.3
3.0*1.9*2.5
3.0*2.15*2.6
3.5*2.1*2.6
4.3*2.2*3.6
weight of machine(ton)
3.0
4.5
6.5
7.8
12.5
1.How to tell us your enquiry?
:You can contact us by email, phone call, fax, Instant Messenger (Trademanager, WhatsApp, Skype) and let us know your requirement.
2.Are you manufacturer or trading company ?
We are industrial manufacturer, which locates in Zhangjiagang city over 18years .
3.Where is your factory?
Our Factory is located in Zhangjiagang City, it is very near to Shanghai and Wuxi (airplame and train both available). If you arrive at Shanghai or Wuxi, we can pick you up to visit our factory.
4. Do you have any technical supports with your Beverage Filling Machines?
Yes, We have a professional team of engineers who owned many installation, debug and training experiences abroad, are available to service machinery overseas.
We Warmly Welcome Customers All Over The World To Our Company.If You Have Interests In Our Products. Please Contact Us If You Have Any Problems.
20 Liters HDPE Bottle Automatic Extrusion Blow Molding /Moulding Machine
Model NO.: JMX
Material: Ss304/316
Certificate: Ce,ISO,SGS
Electrics: Siemens,Mitsubishi,etc
After Sales Service: Engineer Overseas Working
Suitable Product: Jerry Can Water Tank Plastic Drum Bottle Container
Market: Global
Power: 380V or Customer Made
Color: Blue/Yellow/White/Orange
Warranty: Two Years
Exchange Parts: Free
Trademark: Proman
Transport Package: Wooden Cases
Specification: 4.5m*2.1m*2.5m
Origin: Jiangsu, China
HS Code: 8422301090
20 Liters HDPE Bottle Automatic Extrusion Blow Molding /Moulding Machine
Product Introduction
Advantages
1. Stable performance with advanced PLC.
FAQ
Â